Warning: fopen(/home/virtual/kwjs/journal/upload/ip_log/ip_log_2024-03.txt): failed to open stream: Permission denied in /home/virtual/lib/view_data.php on line 88 Warning: fwrite() expects parameter 1 to be resource, boolean given in /home/virtual/lib/view_data.php on line 89 Ti-6Al-4V의 AM에서 기계적 성질에 미치는 Interpass Peening의 영향

Ti-6Al-4V의 AM에서 기계적 성질에 미치는 Interpass Peening의 영향

The Effect of Interpass Peening on Mechanical Properties in Additive Manufacturing of Ti-6Al-4V

Article information

J Weld Join. 2017;35(2):6-12
변재규*, 이희준**, 조상명***,
* 부경대학교 대학원 신소재시스템공학과
* Dept. of Materials System Engineering, Graduate School, Pukyong National Univ., Busan 48547, Korea
** 현대로템(주) 중기사업본부
** Defense Inducstrial Division, Hyundai Rotem Company, Changwon 51407, Korea
*** 부경대학교 신소재시스템공학과
*** Dept. of Materials System Engineering, Pukyong National University, Busan 48547, Korea
Corresponding author : pnwcho@pknu.ac.kr
Received 2017 April 4; Revised 2017 April 19; Accepted 2017 April 24.

Abstract

Ti-alloys have high specific strength and are widely used for the filed of space aeronautics plant. However, it is difficult to process Ti-Alloys due to its high yield strength and it cannot raise the machining speed because it has a possibility of catching fire while processing. In order to reduce the number of processes for the Ti-alloys, the researches related to Additive Manufacturing(AM) have been actively carried out at the moment. As for the initial stage of AM market related to Ti-alloys, it started to use the raw material of powder metal, and it is currently being developed based on welding.

In this study, Interpass peening reduced the size of the primary β grain in the z-axis direction, increased the nucleation site of α-colony, and decreased the length and width of α laths as though interpass rolling. Interpass peening leads to an increase in yield/ultimate tensile strength without decrease elongation, resulting decrease in anisotropy of the material.

1. 서 론

Additive manufacturing(AM)은 CAD도면의 정보로 제품을 얇은 층의 형태로 연속적으로 적층하여 원하는 형상의 제품을 만들어내 것으로 대중적으로는 3D printing이라고 불린다1). 금속AM은 첨가되는 재료의 형상에 따라 크게 분말/와이어 방식으로 나누어지게 되며, Table 1은 금속AM의 분류를 나타내고 있다2). 금속AM은 제품의 형상과 비슷하게 적층함으로서 가공량을 최소화 할 수 있으며, Ti, Inconel, STS 등 고가의 소재에 적합하다.

Classification of metal AM process2)

특히 Ti합금은 높은 비강도를 가져 항공·우주, 플랜트, 자동차 등의 분야에 널리 사용되고 있지만, 높은 항복강도로 인해 절삭가공이 어렵고 가공시 화재발생 위험으로 가공속도를 높이지 못해 가공량이 많아질수록 제조원가는 상승한다. 가공전 제품무게와 최종제품의 무게의 비를 뜻하는 Buy To Fly(BTF)가 높아질수록 가공량이 많아져 제조원가는 증가한다. BTF를 줄이기 위하여 해외에서는 난가공성 소재인 Ti-6Al-4V의 AM연구가 활발히 진행 중이다3-7).

금속AM은 용융풀이 응고하면서 열이 전도되는 방향과 반대로 조직이 성장해 나간다. 이러한 epitaxial grain growth는 이전 층의 grain이 부분적으로 재용융되어 결정의 성장방향을 결정하는 예비 핵의 역할을 하고, 다음 층의 grain 성장방향은 이전 층과 동일하게 된다.

Fig. 1은 Fude Wang 등8)이 Wire+Arc Additive Manufacturing(WAAM)공정으로 Ti-6Al-4V을 적층하였을 때 나타난 단면으로서 z축 방향으로 길게 성장한 primary β grain의 주상조직을 볼 수 있다. 이러한 epitaxial grain growh로 인하여 적층 제품은 기계적 성질의 방향성이 나타나게 된다. 금속 AM에서 발생하는 상기와 같은 기계적 성질의 방향성을 감소시킬 수 있는 공정 개발이 필요하다.

Fig. 1

Montage of macrostructure of pulse GTAW deposition Ti-6Al-4V wall8)

본 연구는 용착속도 TIG용접 아크를 열원으로 한 금속 AM에서 Ti-6Al-4V의 적층하여 z축 방향의 기계적 성질을 x축 방향과 동등수준으로 향상시키기 위하여 interpass peening의 영향을 검토하는 것을 목적으로 한다.

2. 실험 방법

2.1 적층방법

TIG용접을 이용한 Ti-6Al-4V 적층 실험은 기판모재 200mm(L) × 100mm(W) × 2mm(t)의 ASTM Grarde 5를 사용하였으며, 실험에 사용된 와이어는 Φ1.2 ERTi-5를 사용하였다. 재료의 화학성분은 Table 2Table 3에서 표시하고 있다.

Chemical composition of base metal(ASTM Grade 5)

Chemical composition of filler metal(AWS ERTi-5) wt.%

적층실험은 Fig. 2의 모식도와 같이 1layer 1pass방식으로 비드폭은 약 14mm, 층당 높이는 1.5mm가 되도록 설계하여 층간온도를 150°C로 유지하면서 적층하였다. 각 시험편당 최종 높이가 약 100mm가 되도록 설계하여 70layer를 적층하였다.

Fig. 2

Schematic of deposition 1layer 1pass Ti-6Al-4V

AM 적층 조건은 Table 4에 나타냈다. 190A의 전류로 약 1.0kg/h의 적층속도로 적층을 하였고 벽면 끝에서의 용융풀 흘러내림을 방지하기 위하여 오실레이션을 사용하였다. Ti-6Al-4V 적층 시에 자주 발생하는 표면산화 방지를 위하여 trail shielding 장치를 사용하였다. 단면 에칭은 1.5%HF + 4.5%HNO3 + 증류수 혼합용액을 사용하여 30초 동안 부식시켜 미세조직을 검토하였다.

Condition of AM

2.2 Interpass peening 방법

Ti-6Al-4V을 적층할 때 hammer peening machine으로 층마다 용접비드 표면에 peening을 적용하였다. Fig. 3과 같이 적층이 끝나고 나면 표면산화 없는 반짝반짝하고 매끄러운 표면이 나타나고 소성변형으로 인해 울퉁불퉁하게 되도록 표면 전체를 peening하여 다음 층을 적층하였다.

Fig. 3

Before/after bead appearance of as-deposited Ti-6Al-4V by interpass peening

2.3 시험편 채취위치

Ti-6Al-4V 적층물의 Interpass peening 적용 여부에 따라서 Fig. 4의 모식도와 같이 x, z축으로 각각 인장시험편을 채취하였다.

Fig. 4

Schematic diagram of collected location of tensile test specimen

3. 결과 및 고찰

3.1 Ti-6Al-4V 적층물 외관 및 단면

3.1.1 Ti-6Al-4V without peening

Peening을 적용하지 않고 1layer 1pass의 방법으로 70층을 적층한 적층물의 외관과 단면을 각각 Fig. 5, Fig. 6에 나타내었다.

Fig. 5

Appearance of Ti-6Al-4V deposition without peening

Fig. 6

Cross section and microstructure of Ti-6Al-4V deposition without peening

매크로 단면사진에서 주상정이 z축 방향으로 성장한 모습을 확인할 수 있다. 위치에 관계없이 전체적으로 Wid- manstatten α상과 길쭉한 colony α상이 혼합되어 나타는 것을 확인하였다.

3.1.2 Ti-6Al-4V with peening

1layer 1pass로 interpass peening을 적용한 적층물의 외관과 단면은 Fig. 7, Fig. 8에 각각 나타내었다. 폭이나 높이에서 큰 차이가 없으나 단면에서 거대한 주상정이 감소되고 미세화된 β grain을 확인 할 수 있었다.

Fig. 7

Appearance of Ti-6Al-4V deposition with peening

Fig. 8

Cross section and microstructure of Ti-6Al-4V deposition with peening

미세조직은 전체적으로 위치에 관계없이 Widmanstatten α상이 나타났다.

3.2 Interpass plastic working에 따른 Ti-6Al-4V 적층물의 기계적 성질 검토

Fig. 9에 전체적인 항복/인장강도를 비교하여 나타내었다. 항복/인장강도는 x축에 비하여 z축이 감소하는 경향이 나타났고, 이는 z축으로 길게 성장하는 주상정의 영향으로 판단된다. Peening을 적용하지 않은 적층물의 x축 시험편은 항복/인장강도 모두 AWS spec.을 만족했지만, z축 시험편은 항복/인장강도가 현저히 감소하여 AWS spec.에 만족하지 못하였다.

Fig. 9

Comparison of yield/ultimate tensile strength by deposition method and axis

반면에 층마다 peening을 적용한 적층물의 시험편은 항복/인장강도가 기존에 비하여 전체적으로 증가하였고, z축에서의 항복/인장강도가 x축과 비슷하게 유지되어 x축과 z축 시험편모두 AWS spec.을 만족하였다.

Fig. 10에 나타낸 연신율의 경우는 모든 시험편이 AWS spec.을 만족하였으며 peening을 적용하지 않은 z축의 시험편에서 가장 높은 연신율 값을 얻을 수 있었다. 이는 z축의 항복강도 저하에 의한 연성증가로 나타난 결과라고 판단된다. x축의 경우는 peening을 적용한 시험편에서 연신율이 소폭 증가하였다.

Fig. 10

Comparison of elongation by deposition method and axis

Fig. 11은 Martina 등9)에 의해 rolling 하중을 0, 50kN, 75kN 세 가지 조건으로 적층한 Ti-6Al-4V 적층물의 기계적 성질을 비교한 그래프이다. Vertical (z-axis) 방향과 horizontal(x-axis) 방향 모두 rolling 하중이 증가할수록 항복/인장강도가 증가하는 경향을 보였다.

Fig. 11

Comparison of rolled WAAM specimens against unrolled ones (error bars indicate standard deviation), specification minima, and wrought Ti-6Al-4V9)

연신율은 horizontal 방향의 경우 하중 50kN에서 소폭 감소하였다가 75kN에서는 다시 증가하였고, Vertical 방향의 경우 rolling 하중이 증가할수록 연신율이 감소하는 것을 볼 수 있다.

Vertical 방향과 horizontal 방향의 기계적 성질을 비교해보면 rolling을 하면 항복/인장강도, 연신율이 거의 비슷한 값을 가지면서 본 연구의 interpass peening과 유사하게 재료의 이방성이 없어지는 것을 볼 수 있다.

3.3 Interpass plastic working에 따른 Ti-6Al-4V 적층물의 미세조직 검토

3.3.1 Primary β grain size 비교

Ti-6Al-4V의 금속 AM에서 Alphons Anandaraj 등10)Fig. 12와 같이 interpass rolling 하중에 따른 미세조직을 관찰하였고, Colegrove 등11-12)Table 5와 같이 rolling 하중에 따른 primary β grain 크기와 α lath 길이를 측정하였다.

Fig. 12

Optical and SEM microstructure of as deposited Ti-6Al-4V from (a) as-built, (b) rolled at 50kN, (c) rolled at 75kN10)

Primary grains size and alpha laths length and width by interpass rolling load11)

Fig. 13은 본 연구에서 primary β grain 크기를 비교하기 위하여 광학현미경으로 촬영한 Ti-6Al-4V 적층물의 미세조직이다. Table 6은 β grain 크기를 나타낸 것이며, Ti-6Al-4V 금속 AM시에 interpass peening을 미적용하면 6*19.1mm, 적용하면 460μm로 primary β grain의 크기가 현저히 감소되었다.

Fig. 13

Optical microstructure of Ti-6Al-4V deposition with TIG welding(16x)

Primary β grain size of Ti-6Al-4V deposition with interpass peening

이 현상은 interpass rolling을 적용했을 때9)와 같이 interpass peening을 적용하면 소성변형으로 인하여 내부에 dislocation density가 증가하게 된다. 다음 층을 적층할 때 가해진 열이 재결정을 발생시키고, 소성변형으로 재료 내부의 저장된 에너지가 증가하여 핵생성을 더욱 활발하게 일으키고, primary β grain의 수가 증가하여 β grain의 사이즈가 감소하게 된다.

3.3.2 α laths의 길이와 폭 비교

Fig 14는 광학현미경으로 Ti-6A-4V 적층물을 800배로 확대한 미세조직이다. α laths의 길이와 폭을 측정하였고 그 결과를 Table 7에 나타내었다. Interpass peening 미적용 시험편에서 α laths의 길이는 25.5μm, α laths의 폭은 각각 1.4μm으로 나타났다. Interpass peening 적용시험편은 α laths의 길이는 14.8μm, α laths의 폭은 0.8μm로 interpass peening을 적용하면 α laths의 길이와 폭이 모두 감소하는 경향을 보인다.

Fig. 14

Optical microstructure of Ti-6Al-4V deposition with TIG welding(800×)

α laths length and width of Ti-6Al-4V deposition with interpass peening

위의 결과는 interpass rolling의 하중이 증가할수록 α laths의 길이와 폭이 감소하는 것과 같은 경향으로 interpass peening을 적용하면 primary β grain 크기가 감소되고, α colony의 핵 생성 site가 증가하여 α 상의 성장이 서로 방해됨으로서 α lath의 길이와 폭이 모두 감소되는 것으로 판단된다.

4. 결 론

Ti-6Al-4V을 TIG용접 아크를 열원으로 한 금속AM 장치로 적층하여 interpass peening이 적층물의 기계적 성질에 미치는 영향에 대하여 검토한 결과 다음과 같은 결론을 얻었다.

1) Ti-6Al-4V의 금속 AM에서 interpass plastic working 없이 적층할 경우 epitaxial grain growth로 인하여 z축의 항복/인장강도는 감소하게 되며, 최종 적층물은 기계적 성질의 이방성이 발생한다.

2) Interpass peening을 진행할 경우 interpass rolling과 마찬가지로 z축방향의 primary β grain 크기는 감소되고, α colony의 핵생성 site가 증가하며, α laths의 길이와 폭이 감소된다. 이로 인해 조직미세화로 연신율의 감소 없이 항복/인장강도가 증가하여 재료의 이방성이 감소하게 된다.

3) 본 연구의 interpass peening방식은 portable 방식으로 interpass rolling과 비교하여 금속 AM의 현장에서 좀 더 유연하게 적용이 가능할 것으로 판단된다. 또한 곡선과 다양한 벽 두께를 가지고 있는 적층물의 제작에서 interpass rolling에 비해 interpass peening의 적용이 유리할 것으로 판단된다.

후 기

본 연구는 부경대학교 자율창의학술연구비로 연구되었습니다.

References

1. ASTM, F2792-12a. Standard Terminology for Additive Manufacturing Technologies
2. Byun Jae-Gyu, Cho Sang-Myung. Trend of Metal 3D Printing by Welding. J. of Welding and Joining 34(4)2016;:1–8. (in Korean).
3. Kang Min-Cheol, Ye Dea-Hee, Go Geun-Ho. International Development Trend and Technical Issues of Metal Additive Manufacturing. J. of Welding and Joining 34(4)2016;:9–16. (in Korean).
4. Horii Toshihide, Soshu Kirihara, Yoshinari Miyamoto. Freeform fabrication of Ti-Al alloys by 3D micro- welding. Intermetallics 16(11)2008;:1245–1249.
5. Ma Yan, et al. The effect of location on the microstructure and mechanical properties of titanium aluminides produced by additive layer manufacturing using in-situ alloying and gas tungsten arc welding. Materials Science and Engineering A 6312015;:230–240.
6. Baufeld Bernd, Omer Van der Biest. Mechanical properties of Ti-6Al-4V specimens produced by shaped metal deposition. Science and technology of advanced materials 10(1)2009;:015008.
7. Szost Blanka A, et al. A comparative study of additive manufacturing techniques, Residual stress and microstructural analysis of CLAD and WAAM printed Ti-6Al-4V components. Materials & Design 892016;:559–567.
8. Wang Fude, Stewart W. Williams, Rush M. T. Morphology investigation on direct current pulsed gas tungsten arc welded additive layer manufactured Ti6Al4V alloy. Int J Adv Manuf Technol 572011;:597–603.
9. Martina Filomeno, et al. Investigation of the benefits of plasma deposition for the additive layer manufacture of Ti-6Al-4V. Journal of Materials Processing Technology 212(6)2012;:1377–1386.
10. Antonysamy , Alphons Anandaraj. Microstructure, texture and mechanical property evolution during additive manu facturing of Ti6Al4V alloy for aerospace applications University of Manchester for the degree of Doctor of Philosophy in the faculty of Engineering and Physical Sciences; 2012.
11. Colegrove Paul, Stewart Williams. High deposition rate high quality metal additive manufacture using wire+arc technology. 2012;
12. Donoghue J, et al. The effectiveness of combining rolling deformation with Wire-Arc Additive Manufacture on β-grain refinement and texture modification in Ti-6Al-4V. Materials Characterization 1142016;:103–114.

Article information Continued

Table 1

Classification of metal AM process2)

Material Power source Process Company Deposition rate
PBF Powder based Laser SLS(Selective Laser Sintering) EOS, 3D systems, TPM, Farsoon, etc. 0.1~0.2kg/h
DMLS(Direct Metal Laser Sintering) EOS 0.1~0.2kg/h
SLM(Selective Laser Melting) SLM Solutions, 3D systems, Realizer, Concept laser, etc. 0.1~0.3kg/h
Electron beam EBM(Electron Beam Melting) ARCAM 0.1~0.2kg/h
DED Laser LENS(Laser Engineered Net Shaping) Optomec 0.1~2kg/h
DMD(Direct Metal Deposition) DM3D 0.1~2kg/h
DMT(Direct Metal Tooling) InssTek 0.1~2kg/h
CLAD(Construction Laser Additive Direct) BeAM 0.1~2kg/h
Solid filler based Electron beam EBAM(Electron Beam Additive Manufacturing) Sciaky ~9kg/h
GTAW, GMAW arc WAAM(Wire Arc Additive Manufacturing) Cranfield Univ. ~4kg/h
GMAW arc DML(Direct Metal Lamination) MUTOH ~4kg/h
ADED(Arc Directed Energy Deposition) EWI ~4kg/h
Plasma arc IFF(Ion Fusion Formation) Honeywell ~3kg/h
RPD(Rapid Plasma Deposition) Norsk titanium ~6kg/h
GTAW arc STAM(Super-TIG Additive Manufacturing) Super-TIG welding ~7kg/h

Fig. 1

Montage of macrostructure of pulse GTAW deposition Ti-6Al-4V wall8)

Table 2

Chemical composition of base metal(ASTM Grade 5)

Ti Al V Fe N C H O
Grade 5 Bal. 5.5~ 6.75 3.5~ 4.5 Max 0.40 Max 0.05 Max 0.08 Max 0.015 Max 0.20

Table 3

Chemical composition of filler metal(AWS ERTi-5) wt.%

Ti Al V Fe N C H O
Grade 5 Bal. 5.5~6.75 3.5~4.5 Max 0.22 Max 0.03 Max 0.05 Max 0.015 0.12~0.20

Fig. 2

Schematic of deposition 1layer 1pass Ti-6Al-4V

Table 4

Condition of AM

Base metal Ti Gr. 5 (100 × 200 × t2)
Filler metal ø1.2 ERTi-5
Stand off 4mm
Current 190A
Welding speed 18cm/min
Shielding gas Ar100% (20/min)
Feed rate 331cm/min
Deposition area 20.8mm2
Deposition rate 1.0kg/h
OS Frequency 1.8Hz
Dwell time 0.1s
Deposition method 1layer 1pass

Fig. 3

Before/after bead appearance of as-deposited Ti-6Al-4V by interpass peening

Fig. 4

Schematic diagram of collected location of tensile test specimen

Fig. 5

Appearance of Ti-6Al-4V deposition without peening

Fig. 6

Cross section and microstructure of Ti-6Al-4V deposition without peening

Fig. 7

Appearance of Ti-6Al-4V deposition with peening

Fig. 8

Cross section and microstructure of Ti-6Al-4V deposition with peening

Fig. 9

Comparison of yield/ultimate tensile strength by deposition method and axis

Fig. 10

Comparison of elongation by deposition method and axis

Fig. 11

Comparison of rolled WAAM specimens against unrolled ones (error bars indicate standard deviation), specification minima, and wrought Ti-6Al-4V9)

Fig. 12

Optical and SEM microstructure of as deposited Ti-6Al-4V from (a) as-built, (b) rolled at 50kN, (c) rolled at 75kN10)

Table 5

Primary grains size and alpha laths length and width by interpass rolling load11)

As-built 50kN 75kN
Primary β grains 3×30mm 124μm 89μm
α laths length 21.1μm 15.5μm 7.7μm
α laths width 1.2μm 1.0μm 0.7μm

Fig. 13

Optical microstructure of Ti-6Al-4V deposition with TIG welding(16x)

Table 6

Primary β grain size of Ti-6Al-4V deposition with interpass peening

Without peening With peening
Primary β grain size 6×19.1mm 460μm

Fig. 14

Optical microstructure of Ti-6Al-4V deposition with TIG welding(800×)

Table 7

α laths length and width of Ti-6Al-4V deposition with interpass peening

Without peening With peening
α laths length 25.5μm 14.8μm
α laths width 1.4μm 0.8μm